中央供料系統（集中供料系統）稱重式混料機，吸料機，吸粉機，真空上料機，氣力輸送機，真空加料機，中央供料系統廠家,提供注塑機中央供料系統、塑料中央供料系統、自動供料系統、注塑機集中供料系統，模溫機(壓鑄模溫機），工業冷水機，色母機，塑料粉碎機，高速脫油機，塑料干燥機，三機一體除濕機（塑料除濕干燥機），真空輸送機，輸送稱重系統，金屬分離器，。
產品中心
PRODUCT CENTER
- 聯系人 : 曹鏡森先生
- 聯系電話 : 0769-82226193
- 傳真 : 0769-82226193
- 移動電話 : 15989458768
- 地址 : ** 廣東省東莞市大朗鎮仙村仙一區99號
- Email : caojingshen@126.com
- 郵編 : 523792
- 公司網址 : http://accfirst.com
- MSN : caoshingcer@126.com
- QQ : 454992321
- 聯系人 : 曹鏡森
- 聯系電話 : 0769-82226193
- 傳真 : 0769-82226193
- 公司網址 : http://accfirst.com/
產品詳情
簡單介紹：
自動加料系統說明書
I.啟動前的準備工作
1.檢查送料器的氣源壓力是否正常（0.5-0.6 MPa）以及電源是否打開; 2，檢查管件是否正確連接; 3，檢查各種材料是否準備好;
II。自動加料系統說明書系統操作
詳情介紹：
自動加料系統說明書
I.啟動前的準備工作
1.檢查送料器的氣源壓力是否正常（0.5-0.6 MPa）以及電源是否打開; 2，檢查管件是否正確連接; 3，檢查各種材料是否準備好;
II。自動加料系統說明書系統操作
1.打開控制柜中的主電源開關，將控制面板上的電源旋鈕開關轉到“開”位置，電源指示燈亮;
2.在觸摸屏下校準和清，除兩個稱重系統監視器的值;
3.當觸摸屏操作進入功能選擇屏幕時，可以根據工藝要求進入“參數設置”，設置“配料參數”和“時間參數”。
您還可以查看“報警記錄”和“記錄查詢”; 4，進入“操作模式”選擇“手動”或“自動”，然后單擊“確認”進入操作界面; 5，如果選擇“手動”，可以根據工藝要求輕觸，需要打開或關閉的機構，紅色為關閉狀態，綠色為打開狀態;設置真空給料機的控制面板。頂部的“進給”和“進給”時間可以通過“開/關”實現;
6.如果選擇“自動”，則必須根據工藝要求設置“配料參數”和“時間參數”。當外部設備準備就緒時，按下控制柜上的“配料開始”按鈕，然后按“外部準備完成”按鈕。系統自動開始運行并在達到設定值后自動停止。
7.混合完成后，控制面板上的電源旋鈕開關可以在“關閉”位置關閉。一種
3.自動加料系統說明書備注
1.自動加料系統的送料時間短于送粉時的送料時間，送料時間長于送料時的送料時間。一種或者多種
2.禁止在秤上或附近焊接。 _ 一種或者多種
IV。點檢查和操作要求
1.隨時觀察系統各閥門機構的操作。一種或者多種
2.檢查供氣壓力是否正常，卸料門是否密封以及過濾器是否堵塞。一種或者多種
V.維度，護理和維護
1.定期檢查秤的精度，當秤超出公差時需要校準。在維護時應注意固定秤的運動部件。一種或者多種
3.混合后需要清潔真空供料器
Automatic feeding system manual
I. Preparation before starting
1. Check if the air supply pressure of the feeder is normal (0.5-0.6 MPa) and whether the power supply is open; 2. Check whether the pipe fittings are properly connected; 3. Check whether the various materials are ready;
II. Automatic feeding system manual system operation
1. Open the main power switch in the control cabinet, turn the power knob switch on the control panel to the “on” position, and the power indicator light is on;
2. Calibrate and clear the values of the two weighing system monitors under the touch screen;
3. When the touch screen operation enters the function selection screen, you can enter the “parameter setting” according to the process requirements, and set the “batch parameter” and “time parameter”.
You can also view the “Alarm Record” and “Record Query”; 4. Enter “Operation Mode” and select “Manual” or “Auto”, then click “Confirm” to enter the operation interface; 5. If you select “Manual”, you can The process requires light touch, the mechanism that needs to be opened or closed, the red is off, the green is on; the vacuum feeder's control panel is set. The “feed” and “feed” times at the top can be achieved by “on/off”;
6. If you select "Automatic", you must set the "Batch Parameters" and "Time Parameters" according to the process requirements. When the external device is ready, press the “Batch Start” button on the control cabinet and press the “External Ready to Complete” button. The system automatically starts running and stops automatically when the set value is reached.
7. When the mixing is complete, the power knob switch on the control panel can be turned off in the “off” position. One kind
3. Automatic feeding system manual remarks
1. The feeding time of the automatic feeding system is shorter than the feeding time when feeding, and the feeding time is longer than the feeding time when feeding. One or more
2. It is forbidden to weld on or near the scale. _ one or more
IV. Point check and operation requirements
1. Observe the operation of each valve mechanism of the system at any time. One or more
2. Check if the air supply pressure is normal, whether the discharge door is sealed and whether the filter is clogged. One or more
V. Dimensions, care and maintenance
1. Regularly check the accuracy of the scale and calibrate when the scale is out of tolerance. Pay attention to the moving parts of the fixed scale during maintenance. One or more
3. Need to clean the vacuum feeder after mixing
I.啟動前的準備工作
1.檢查送料器的氣源壓力是否正常（0.5-0.6 MPa）以及電源是否打開; 2，檢查管件是否正確連接; 3，檢查各種材料是否準備好;
II。自動加料系統說明書系統操作
1.打開控制柜中的主電源開關，將控制面板上的電源旋鈕開關轉到“開”位置，電源指示燈亮;
2.在觸摸屏下校準和清，除兩個稱重系統監視器的值;
3.當觸摸屏操作進入功能選擇屏幕時，可以根據工藝要求進入“參數設置”，設置“配料參數”和“時間參數”。
您還可以查看“報警記錄”和“記錄查詢”; 4，進入“操作模式”選擇“手動”或“自動”，然后單擊“確認”進入操作界面; 5，如果選擇“手動”，可以根據工藝要求輕觸，需要打開或關閉的機構，紅色為關閉狀態，綠色為打開狀態;設置真空給料機的控制面板。頂部的“進給”和“進給”時間可以通過“開/關”實現;
6.如果選擇“自動”，則必須根據工藝要求設置“配料參數”和“時間參數”。當外部設備準備就緒時，按下控制柜上的“配料開始”按鈕，然后按“外部準備完成”按鈕。系統自動開始運行并在達到設定值后自動停止。
7.混合完成后，控制面板上的電源旋鈕開關可以在“關閉”位置關閉。一種
3.自動加料系統說明書備注
1.自動加料系統的送料時間短于送粉時的送料時間，送料時間長于送料時的送料時間。一種或者多種
2.禁止在秤上或附近焊接。 _ 一種或者多種
IV。點檢查和操作要求
1.隨時觀察系統各閥門機構的操作。一種或者多種
2.檢查供氣壓力是否正常，卸料門是否密封以及過濾器是否堵塞。一種或者多種
V.維度，護理和維護
1.定期檢查秤的精度，當秤超出公差時需要校準。在維護時應注意固定秤的運動部件。一種或者多種
3.混合后需要清潔真空供料器
Automatic feeding system manual
I. Preparation before starting
1. Check if the air supply pressure of the feeder is normal (0.5-0.6 MPa) and whether the power supply is open; 2. Check whether the pipe fittings are properly connected; 3. Check whether the various materials are ready;
II. Automatic feeding system manual system operation
1. Open the main power switch in the control cabinet, turn the power knob switch on the control panel to the “on” position, and the power indicator light is on;
2. Calibrate and clear the values of the two weighing system monitors under the touch screen;
3. When the touch screen operation enters the function selection screen, you can enter the “parameter setting” according to the process requirements, and set the “batch parameter” and “time parameter”.
You can also view the “Alarm Record” and “Record Query”; 4. Enter “Operation Mode” and select “Manual” or “Auto”, then click “Confirm” to enter the operation interface; 5. If you select “Manual”, you can The process requires light touch, the mechanism that needs to be opened or closed, the red is off, the green is on; the vacuum feeder's control panel is set. The “feed” and “feed” times at the top can be achieved by “on/off”;
6. If you select "Automatic", you must set the "Batch Parameters" and "Time Parameters" according to the process requirements. When the external device is ready, press the “Batch Start” button on the control cabinet and press the “External Ready to Complete” button. The system automatically starts running and stops automatically when the set value is reached.
7. When the mixing is complete, the power knob switch on the control panel can be turned off in the “off” position. One kind
3. Automatic feeding system manual remarks
1. The feeding time of the automatic feeding system is shorter than the feeding time when feeding, and the feeding time is longer than the feeding time when feeding. One or more
2. It is forbidden to weld on or near the scale. _ one or more
IV. Point check and operation requirements
1. Observe the operation of each valve mechanism of the system at any time. One or more
2. Check if the air supply pressure is normal, whether the discharge door is sealed and whether the filter is clogged. One or more
V. Dimensions, care and maintenance
1. Regularly check the accuracy of the scale and calibrate when the scale is out of tolerance. Pay attention to the moving parts of the fixed scale during maintenance. One or more
3. Need to clean the vacuum feeder after mixing
